Camlocs have become the OEM chassis
constructor's virtually universal choice for bodywork attachment.
We stock the
cross recess (Phillips) version of
the 4002 series studs and receptacles detailed below. All
dimensions are in inches.
Stud
Series
Stud
Diameter
Grommet
Stud
Retaining
Split Ring
Working
Strength
Ultimate Strength
4002
.171
.166
required in
top panel
-16 and up
(4002SW)
700 LB
1050 LB
To
Determine Stud Part Number
1. Select
receptacle to be used: illustration above
2. Determine
"G" thickness per grommet
illustration. Note: add maximum "D"
dimension to "G" when using plus
flush grommets (i.e. 4002-N, 4002-0, 4002-N3,
4002P3, 4002P4)
3. See Stud
table below to determine stud dash number:
read stud dash number under receptacle type.
4. -or- measure
existing stud and read length from following
chart
Stud
Selection
"G"
Total
Thickness
214-16
244-16
"G"
Total
Thickness
214-16
244-16
.081 -
.110
2
3
.441 -
.470
14
15
.111 -
.140
3
4
.471 -
.500
15
16
.141 -
.170
4
5
.501 -
.520
16
17
.171 -
.200
5
6
.531 -
.560
17
18
.201 -
.230
6
7
.561 -
.590
18
19
.231 -
.260
7
8
.591 -
.620
19
20
.261 -
.290
8
9
.621 -
.650
20
21
.291 -
.320
9
10
.651 -
.680
21
22
.321 -
.350
10
11
.681 -
.710
22
23
.351 -
.380
11
12
.711 -
.740
23
24
.381 -
.410
12
13
.741 -
.770
24
25
.411 -
.440
13
14
.771 -
.800
25
26
40S5
STUD LENGTHS
STUD
DASH NO.
"S"
LENGTH
STUD
DASH NO.
"S"
LENGTH
STUD
DASH NO.
"S"
LENGTH
1
.650
8
.860
15
1.07
2
.680
9
.890
16
1.10
3
.710
10
.920
17
1.13
4
.740
11
.950
18
1.16
5
.770
12
.980
19
1.19
6
.800
13
1.01
20
1.22
7
.830
14
1.04
21
1.25
Grommets
Ring
Retained Grommets (see illustrations above)
PART
NO.
STYLE
P
(MAX)
A
B
C
D
G
(MINIMUM)
4002-N2.
plus flush
.025
.625
.617
.201
.193
.082
.074
.069
.063
.053
4002-N
plus flush
.065
.625
.617
.201
.193
.122
.114
.029
.023
.091
4002-0
plus flush
.094
.625
.617
.202
.192
.157
.137
.029
.023
.116
4002-N3
plus flush
.128
.876
.867
.252
.244
.128
.120
.054
.048
.150
4002-G
flush
.074
N/A
.191
.183
.132
.124
N/A
.090
4002-H
flush
.117
N/A
.201
.193
.173
.167
N/A
.150
Flare
Retained Grommets
Flare retained grommets will
accommodate relatively thick panels often eliminating the
need for back counterboring. Flared grommets should
also be specified when axial grommet movement must be
restricted. Please note that part numbers shown following
are basic part numbers only. See table for "P"
panel thickness, "L" dimension and required
grommet length dash number. All dimensions are in inches.
